Sea & Land Cutting Assets

800-957-4344

760-868-6748

Civilians

---

Municipalities

---

Militaries

---

• Repair
• Maintenance
• Fabrication
• Scrap
• Dismantling
• Salvage
• Emergency
• Tactical

---

Cut, gouge, pierce, or melt any known material using a highly controllable ten-thousand degree ionized particle stream.

---

Recent developments include patented arc consumables, 24 volt ignition systems and digital umbilical control boxes to replace outdated knife switches. Our customers range from repair and maintenance professionals to tactical military personnel. Wherever speed, power and versatility are needed do what other customers facing impossible cutting tasks do... call MagnumUSA.

 

Join our growing dealer network and help us continue providing the best products and service on the market.

 

GENERAL SURVIVAL TIPS

How to survive on water or land.

Avoid three leaf plants and eight legged insects. Eating plants: Better to avoid plants unless you are an expert since most will lead to illness or death.

Finding water: Find the lowest spot in an area and dig. Since animals also require water, observe their habits.

Boiling water: If it is boiling, it is good enough.

Filtering water: Let it stand for twelve hours. Make a filter out of straw, sand, crushed rock, charcoal, or cloth. Use fire ash to remove the odor. Let stand 45 minutes prior to drinking. Fire ash is also good for an upset stomach and to keep your teeth clean.

Critters: Stick to critters with fur, fish, birds and eggs. Also, six legged insects are OK. Eight legged insects tend to be poisonous. Avoid any creature with red; natures warning. The Coral snake is a good example of nature using color as a warning of danger.

Backpack uses:

• A vessel capsizes a mile from shore. The Final Solution is strapped on by the pilot and used like a jet pack to propel the pilot and two other crew members to shore. The 3000 psi charge will push over 150 psi with its standard oxygen regulator, or much higher if opening the cylinder valve direct.
• A fellow diver becomes trapped inside a cave. You dive in with the Final Solution fitted with a Y connection. The diver has emergency backup breathing oxygen while the rescue diver uses the same cylinder to cut through debris trapping the diver.
• Your lifeboat develops a leak. You repair it but it but you lost valuable air pressure. You connect the Final Solution to the lifboat fill hose and return the pressure to normal operating range with plenty of oxygen to spare for other uses.
• An earthquake causes buildings to collapse. Survivors are trapped in the wreckage. You use the Final solution to rapidly cut through the mangled and twisted iron to allow the survivors to escape their otherwise egregious fate.
• A cave in at a mine has left several workers trapped in an underground compartment. It will take time for a rescue crew to respond. One of the workers has access to the Final Solution which will allow the miners to breathe oxygen while using their power station to power lights and keep their cell phones working.
• A vessel's rudder becomes entangled with wire from wreckage hidden underwater making navigation impossible. It may takes hours, if not days for rescue to arrive. The vessel's owner dives overboard and cuts through the wire entanglement in seconds, freeing the vessel's rudder and avoiding a serious situation.
• You are on a life raft in the middle of the ocean. Food is nonexistent. You insert a blow dart tube into the Final Solution and point it overboard at passing fish. The dart is powered by 150 pounds of pressure driven down a small tube, driving the dart at sufficient pressure to kill or stun the fish.
• You are exploring a remote area of the mountains and the weather unexpectantly turns foul. Rain keeps chances of a fire minimal. You have two choices. You can use your power station to power a heating blanket and keep warm for the night. You can also shave wood from a dry spot on a large tree and ignite the shavings using steel wool and your power station, even if wet.
• You are driving in a remote part of the high desert when your encounter a flat tire. You open the trunk and pull the spare. The spare tire has lot pressure over time. You attach an inflater adapter to the Final Solution's hose and inflate the spare, avoiding a dangerous situation.
• Use the power base station double prong igniter head to shock sharks so they leave without a trail of kill blood that only serves to attract more sharks.
• Use a burning flame tube at night as a signal flare. Very bright light intensity will be seen for miles making it ideal for signaling helicopters, rescue planes and coast guard vessels.

 

Magnum has been manufacturing the world's most expedient cutting and welding assets for civilian, municipal and military projects and applications. Over the past fifteen years, Magnum cutting assets have bcome known throughout the world for their speed, power and versatility. The diversity of our sea and land cutting assets are best demonstrated by the diversity of thousands of users ranging from equipment service personnel to elite Navy Seal breachers. Join the growing group of civilian and tactical users arming themselves with the most powerful cutting asset on the market.

Veteran Owned	Cutting Kits MAG2000X™ marine Underwater kit ships with popular Blackhawk cutting torch, two stage regulator, thirty feet of high grade oxygen hose, two boxes of cutting rods, an igniter for shallow work, and knife switch for use with an existing DC welding machine. MAG2000+™ land Arc/Flame cutting kit designed to accommodate both oxyflame cutting tubes and oxyarc cutting rods without modification. This kit is quite popular for repair and maintenance projects and ships ready for connection to your oxygen cylinder. MAG4000™ land Oxy-flame kit cuts, gouges and pierces with 18" or 36" flame tubes that burn at ten-thousand degrees once ignited with a mere 12 volt spart from a common battery. Longer tubes are ideal for heavy equipment pin piercing and removal and powered ignition systems are available. Amphibian Cutting Systems MAG9000™ amphibian backpack Single cylinder ultra lightweight backpack cutting system weighing in at 16 pounds and designed for diverse cutting assignments on land or in underwater situations. A TACTICAL favorite among police departments. Ideal for civil defense and emergency rescue personnel. MAG9002™ amphibian backpack Twin cylinder backpack cutting system offering twice the cutting time from two high pressure oxygen cylinders. Highly recommended for mines since our cutting process has been approved by MSHA as a replacement for air-carbon-arc. No setup. This is the fastest process on the market. MAG9003™ amphibian roller case Another new product: Three cylinder amphibian cutting system and 24 volt remote controlled igniton system. Use it on land or in marine repair applications. Ships with a 50' umbilical, flotable case, cutting tubes and more. Designed for single user applications where topside tenders are not employed. Cutting with Welders MAG2000GW4™ land MAG2000GX4™ marine 400 amp Lincoln Advantage welder and cutting system sufficient for the majority of jobs facing a commercial service personnel. Ships with 100 foot umbilical. Longer lengths available. MAG2000GW5™ land MAG2000GX5™ marine 500 amp Lincoln Advantage welder and cutting system for extreme repair assignments in both commercial and Military settings where higher currents are mandated. MAG2000GW56™ land MAG2000GX56™ marine 500 amp Lincoln Advantage welder and cutting system with lower profile high pressure oxygen cylinders. They are short on stature but long on cutting and easy to fill. Oxyflame Cutting Tubes MAG3818™ land MAG3818X™ marine 3/8" x 18" exothermic cutting tubes, unwrapped style for land and wrapped X style for marine. The most popular cutting tube on the market with the patented 7 spoke carburetor style. MAG3836™ land MAG3836X™ marine 3/8" x 18" exothermic cutting rods, unwrapped style for land and wrapped X style for marine. Longer lengths provide longer cutting times. The tubes can be bent for all position access. Oxyarc Cutting Rods MAG3800™ land MAG3800X™ marine 3/8" x 18" patented oxy-arc cutting rods for 225 amp machines and higher. Pure copper outer tubes with copper coated carbon inner spokes for longer, quieter cutting times per rod. MAG1200™ land MAG1200X™ marine 1/2" x 18" patented oxy-arc cutting rods for 225 amp machines and higher. Larger diameter rods allow for greater oxygen volume and arc size, proving valuable for larger work assignments as encountered with scrap, dismantling and salvage. Cut up to twent minutes with one rod. Wet Welding Rods Wet Welding marine Wet welding electrodes in popular grades for mild steel, stainless steel, and nickel for dissimilar metals. Electrodes are wrapped and sealed for ultimate performance in marine conditions. Umbilicals and Controls UCB marine Digital umbilical control boxes that replace knife switches. Fused up to 500 amps for controlling the voltage of large dc welders when required. Umbilicals marine Cutting/welding umbilicals up to 4/0 diameter and 450' in length. Our longer umbilicals come cross wrapped for abrasion protection. Cutting Torches Torches land Torches marine Popular Blackhawk cutting torches for flame or arc cutting. Flame torches come with thumb control valve. Battery Ignition Systems Ignitions land 12 and 24 volt battery ignition systems for igniting exothermic cutting tubes. Ignitions are independent of torches for ultimate portability and user convenience. Oxygen Regulators Regulators Preset or you set precision oxygen regulators. Oxygen Cylinders Cylinders High pressure composite or steel oxygen cylinders. NAVIGATION Cutting and Welding Products Cutting Kits MAG2000X™ MAG2000+™ MAG4000™ Amphibian Cutting Systems MAG9000™ MAG9002™ MAG9003™ Cutting Systems with Welders MAG2000GX4™ MAG2000GW4™ MAG2000GX5™ MAG2000GW5™ MAG2000GX5+6™ MAG2000GW5+6™ Flame consumables MAG3818X™ MAG3818™ MAG3836X™ MAG3836™ Arc consumables MAG3800X™ MAG3800™ MAG1200X™ MAG1200™ Wet welding electrodes MAG6013X™ MAG7014X™ MAG0310X™ Umbilicals and controls Cutting torches land MAG2001™ MAG4001™ Cutting torches marine MAG2001X™ Ignition systems MAG0021™ MAG0024™ Oxygen regulators Single stage Two stage Oxygen cylinders Composite CONTACT VIDEO DEALERS LINKS Board of Advisors HOME
800-957-4344 toll free or 760-868-6748 stand by alternative

More divers trained on Magnum than any other brand.

customers have visited this page

Instructional video

Featured in WIRED MAGAZINE!

Rated top performer Dun and Bradstreet

A Blackhawk™ cutting torch generates double the temperature of acetylene torches regardless of brand because of its unique ability to ionize metal particles using oxygen. Sublimation is the key and our burning process as it converts metal to a liquid state in seconds due to its ability to destabilize the molecules to a state of disequilibrium, thus allowing for expeditious cutting, gouging or piercing without preheating. The process works so fast there is a much smaller HAZ (heat affected zone) so post weld brittleness is minimal. As the leader in cutting innovation, Magnum Mfg. Inc. has recently developed a 12/24 volt ignition that can also weld. The new ignition provides tactical support in addition to support of field initiatives as encountered in emergency response or emergency field repairs. We call our newest tactical 9000™ series the Final Solution™ because it can cut, gouge, pierce (solder and weld if using our Command Base Power Station) by virtue of its independent ignition system. Multi-tasking is something we have all become accustomed to and the Command Base was designed for that purpose, working in both land and marine settings. When considering catalytic counter intervention strategies, be sure to include the tactical backpack cutting system with its advanced adaptability and "take no prisoners" attitude. When the conclusion appears catastrophic and inescapable, consider a commercial constant that is reliable, dependable and sustainable and can bound over barriers via its bantam weight backpack and focused heat stream. Stun suspeces with stealth and speed while cutting through concealed compartments in order to confiscate contraband from criminals. Show the active arm of authority using this big bad brother of all breachers as our Navy staff members like to call it. Use it for special assignments when stragetic systems must react in seconds as you would expect from an essential extrication asset for land and marine use. Features include adaptability, bendability, extendability, convertability, dependability and certainly formidability as a rapid responder for rural rescue, performing as a personal power pack for box of burning buddies aka commercial construction cutters, coined in the trade as the Breaching Batallion Backpack. From an innovation standpoint, mixing gas is in the past. Consider the sleek, streamlined, simple design of our tactical backpack cutting systems that can deployed using sacrificial tubes. In a marine context, sacrificial tubes are used for salvage purposes to slice through ship wrecks and repair vessels. Operators can now place more emphasis on solving problems.

Consider the advantages in deploying a hand held "particle accelerator in a tube"™ to gain advantage over project initiatives. Operation is uncharacteristically quiet and it cuts like a master of improvisation. One military analyst called it a systematic course of action for gaining advantage over tactical breaching protocols. Who are we to argue? Each of our systems has bees thoroughly tested and easy to operate. They cut with astonishing speed. Several revolutionary break throughs can be seen to bring about a true multi-tasking cutting and welding asset in a compact case. The new consumables burn like no other burning bars, oxygen lances or Slice™ rods. Our law enforcement cutting torch, also known as the tactical thermal breaching torch, is used for breaching in a variety of settings. Our precision land and underwater cutting torches operate on either compressed bottled oxygen or liquid oxygen. Simply put, if medical oxygen is safe enough to breathe, it is safe enough to cut steel. The torch enjoys unrivaled diversity ranging from aircraft maintenance to scrap wrecking yards where a diversity of alloys are encountered ranging from aluminum and stainless steel to cast iron and manganese. The Blackhawk™ torch not only cuts at a ten-thousand degree temperature in flame mode without a welder assist, the same torch can also arc cut using a welder making it quite useful for auto salvage, boat salvage and boat repair. The military cutting torch is unequaled as both a land and a marine cutting torch. Tests show the emergency cutting torch is superior to oxyacetylene cutting equipment through its use of interchangeable collets to accommodate different cutting rod diameters. Although we have described our proprietary process as magmafusion™ welding distributors might have our torch listed under dated terms like exothermic, endothermic, Ultrathermic®, Aquathermic®, sea torch, sea cutting torch, oxy-arc cutting torch, thermal dynamics cutting torch, thermadyne™ air carbon arc gouging torch, oxygen cutting lances, thermolance oxygen lance, superblast cutting rods, aqua lance, surweld, and proweld, but it will not be listed as an oxy-gasoline cutting torch because it uses only oxygen like that sold by air liquide or other popular welding suppliers. Consider a forced entry tactical torch or submersible cutting torch as an indispensible asset to your cutting arsenal, sometimes referred to as an oxygen lance flame cutting torch to round off a rather long list of nomenclature. What is far more important is the process lends itself as the ideal entry torch when it comes to immediate cutting, gouging or piercing any material in seconds particularly as a convenient preparation for arc welding without time consuming grinding. Those building contractors using burning bars, burning rods, burning bars, thermic lances or oxygen lances will find our Blackhawk™ torch far easier to operate and control because of its unique design and lower oxygen regulator. Magnum was the first company that offered an oxygen regulator at the base of the torch to control flame length and is superior in control over gouging rods, making the ultimate maintenance torch. All of our high performance torches use standard brass collets to hold cutting rods and cutting tubes. Rods or tubes made by Caldo®, Oxylance®, Broco® and Arcair® will work in our cutting torch with greater performance according to our factory comparison tests. The Navy Seals recently preferred our cutting torch and cutting tubes to all ot her brands on the market. Commercial construction and heavy equipment is a prime market for our cutting torch when it comes to land projects. Nevertheless, when it comes to the serious challenges of underwater construction, commercial divers and diving organizations will find our torch an indispensible asset. Our customers include heavy construction equipment rental agencies, equipment contractors and contractors in general who have found our cutting torches and cuttring consumables superior to other cutting and welding consumables currently on the market. Simply put, there is no faster or more powerful cutting tool or cutting torch on the market for either land or underwater assignments. Even novices find out Blackhawk™ cutting torch easy to use.

MAGNUMUSA AND BLACKHAWKTORCH ARE TRADEMARKS OF MAGNUM MANUFACTURING INC.

ALL RIGHTS RESERVED. © 2010